01.產品介紹
產品支持magsafe,為了讓您有更高效的充電體驗,請選擇支持PD協議的數據線和點煙器。

-
充電寶電源鍵
-
電量指示燈(充電寶)
-
金屬銅觸點(充電寶)
-
車充狀態指示燈
-
車充金屬銅觸點
02.產品規格
magcar3 |
|
|---|---|
|
輸入(type-c) |
12V=2.5A |
|
輸出(type-c) |
30W |
|
輸出(無線充電) |
15W max |
|
電池容量 |
4200mAh 7.7V |
|
額定能量 |
32Wh |
|
認證 |
CE,FCC,C-tick |
|
尺寸 |
充電寶(114.5*73.5*15.5mm) 車充底座(72.5*72.5*34mm) |
|
重量 |
淨重:0.3kg |
配件點煙器參數 |
|
|---|---|
|
Input:DC |
12V/24V |
|
輸出(Type-c1) |
5V=3A ; 9V=3A ; 12V=3A ; 15V=2.4A ; 20V=1.8A |
|
輸出(Type-c2) |
5V=3A ; 9V=3A ; 12V=3A ; 15V=2.4A ; 20V=1.8A |
|
Type-c1 + Type-c2 Total Out |
72W(max)= 36W(max)+36W(max) |
|
認證 |
CE,FCC,ROHS |
|
尺寸 |
∅28.5mm*68.3mm |
03.產品特點
-
磁吸設計:N52磁鐵強力磁吸,自動對齊,更加穩固。
-
PD30W:相比上一代輸出功率更高。
-
3-in-1充電:支持有線、無線,滿足多種充電需求
04.使用指南

-
安裝支架:把底座螺栓卸下,套在支架球頭上。
-
安裝支架:將支架的球頭按進底座上對應的槽位,擰緊螺栓。
-
固定支架:旋轉通用支架上的旋鈕,確保支架上下兩個部件開口足夠塞進風口。
-
固定支架:將通用支架伸進風口的葉片上,旋轉旋鈕確保支架開口緊緊咬合住風口葉片。
-
連接電源:將電源線(type-c)插進車充底座的接口上。
注意:要使用點煙器上的Type-c口給車充底座供電,不建議使用USB-A口給底座供電。
狀態提示

05.警告
-
請勿拆卸或修改本產品,避免二次故障,拆卸過的產品不在保修範圍內。
-
存放本產品請放置於陰涼幹燥的環境下。
-
使用前請檢查產品是否完整,當發現有任何損壞時,請立即停止使用產品。
-
請勿將本產品投入火中、水中,避免造成短路漏電或損壞產品。
-
在電池膨脹的情況下,停止充電或使用本產品。
-
充電時,產品發熱屬於正常現象,不應影響產品的正常使用。
-
停車時,請切斷車輛對Magcar3的電源,避免車內溫度過高時對產品充電。
06.包裝內容

-
magcar3*1
-
點煙器*1
-
通用支架*1
07.產品認證

01. Product Introduction
The product supports magsafe. To provide you with a more efficient charging experience, please choose data cables and car chargers that support the PD protocol.

-
Power Button of the Power Bank
-
Power Indicator Light (Power Bank)
-
Metal Copper Contacts (Power Bank)
-
Car Charger Status Indicator Light
-
Car Charger Metal Copper Contacts
02. Product Specifications
magcar3 |
|
|---|---|
|
Input (Type-C) |
12V=2.5A |
|
Output (Type-C) |
30W |
|
Output (Wireless Charging) |
15W max |
|
Battery Capacity |
4200mAh 7.7V |
|
Rated Energy |
32Wh |
|
Certification |
CE, FCC, C-tick |
|
Dimensions |
Power Bank (114.5*73.5*15.5mm) Car Charger Base (72.5*72.5*34mm) |
|
Weight |
Net Weight: 0.3kg |
Accessory Cigarette Lighter Parameters |
|
|---|---|
|
Input: DC |
12V/24V |
|
Output (Type-C1) |
5V=3A; 9V=3A; 12V=3A; 15V=2.4A; 20V=1.8A |
|
Output (Type-C2) |
5V=3A; 9V=3A; 12V=3A; 15V=2.4A; 20V=1.8A |
|
Type-C1 + Type-C2 Total Out |
72W(max)= 36W(max)+36W(max) |
|
Certification |
CE, FCC, ROHS |
|
Dimensions |
∅28.5mm*68.3mm |
03. Product Features
-
Magnetic Design: N52 magnet with strong magnetic attraction, auto-alignment, more stable.
-
PD30W: Higher output power compared to the previous generation.
-
3-in-1 Charging: Supports wired and wireless charging to meet various charging needs.
04. User Guide

-
Install Stand: Remove the base bolt and fit it onto the holder ball joint.
-
Install Stand: Push the holder ball joint into the corresponding slot on the base and tighten the bolt.
-
Secure Stand: Rotate the knob on the universal stand to ensure the two opening parts of the stand are wide enough to fit into the air vent.
-
Secure Stand: Insert the universal stand into the blades of the air vent, rotating the knob to ensure the stand's opening tightly grips the air vent blades.
-
Connect Power: Insert the power cable (Type-C) into the interface of the car charger base.
Note: Use the Type-C port on the cigarette lighter to power the car charger base, it is not recommended to use the USB-A port to power the base.
Status Indication

05. Warning
-
Do not dismantle or modify this product to avoid secondary failures; products that have been dismantled are not covered by warranty.
-
Store this product in a cool, dry environment.
-
Please check the product for completeness before use; if any damage is found, stop using the product immediately.
-
Do not throw this product into fire or water to avoid short circuit, leakage, or damage to the product.
-
If the battery swells, stop charging or using this product.
-
It is normal for the product to heat up during charging, and it should not affect the normal usage of the product.
-
When parked, please disconnect the vehicle's power to the Magcar3 to avoid charging when the interior temperature is too high.
06. Package Contents

-
magcar3*1
-
Cigarette Lighter*1
-
Universal Stand*1
07. Product Certification

Leave a Comment